本文主要是介绍华为无线网络的配置——AP上的业务数据采用直接转发模式，希望对大家解决编程问题提供一定的参考价值，需要的开发者们随着小编来一起学习吧！
1.配置接入交换机
[sw1]vlan batch 200 to 203 //创建vlan
[sw1-GigabitEthernet0/0/1]port link-type trunk //与ap相连的端口为trunk
[sw1-GigabitEthernet0/0/1]port trunk pvid vlan 200 //给端口打上管理vlan
[sw1-GigabitEthernet0/0/1]port trunk allow-pass vlan 200 to 202
[sw1-GigabitEthernet0/0/2]port link-type trunk
[sw1-GigabitEthernet0/0/2]port trunk pvid vlan 200
[sw1-GigabitEthernet0/0/2]port trunk allow-pass vlan 200 to 202
[sw1-GigabitEthernet0/0/3]port link-type trunk
[sw1-GigabitEthernet0/0/3]port trunk allow-pass vlan 200 to 203
[sw1-GigabitEthernet0/0/4]port link-type access
[sw1-GigabitEthernet0/0/4]port default vlan 203
2.配置汇聚交换机
[sw2]vlan batch 200 to 203
[sw2-GigabitEthernet0/0/1]port link-type trunk
[sw2-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[sw2-GigabitEthernet0/0/2]port link-type trunk
[sw2-GigabitEthernet0/0/2]port trunk allow-pass vlan all
3.配置AC
[ac]vlan batch 200 to 203
[ac-GigabitEthernet0/0/1]port link-type trunk
[ac-GigabitEthernet0/0/1]port trunk allow-pass vlan 200 to 203
[ac-GigabitEthernet0/0/1]int vlanif200
[ac-Vlanif200]ip add 10.1.200.200 24 //配置管理vlan的地址
4.配置汇聚交换机为网关和DHCP服务器
[sw2-Vlanif200]ip add 10.1.200.1 24
[sw2-Vlanif200]dhcp select global
[sw2-Vlanif201]ip add 10.1.201.1 24
[sw2-Vlanif201]dhcp select global
[sw2-Vlanif202]ip add 10.1.202.1 24
[sw2-Vlanif202]dhcp select global
[sw2-Vlanif203]ip add 10.1.203.1 24
[sw2-Vlanif203]dhcp select global
[sw2]dhcp enable //启动DHCP功能
[sw2]ip pool ap-pool
[sw2-ip-pool-ap-pool]gateway-list 10.1.200.1
[sw2-ip-pool-ap-pool]network 10.1.200.0 mask 24
[sw2-ip-pool-ap-pool]dns-list 114.114.114.114
[sw2-ip-pool-ssid-a1]gateway-list 10.1.201.1
[sw2-ip-pool-ssid-a1]network 10.1.201.0 mask 24
[sw2-ip-pool-ssid-a1]dns-list 114.114.114
[sw2-ip-pool-ssid-a2]gateway-list 10.1.202.1
[sw2-ip-pool-ssid-a2]network 10.1.202.0 mask 24
[sw2-ip-pool-ssid-a2]dns-list 114.114.114.114
[sw2-ip-pool-pc]gateway-list 10.1.203.1
[sw2-ip-pool-pc]network 10.1.203.0 mask 24
[sw2-ip-pool-pc]dns-list 114.114.114.114
5.AP上线的配置
[AC]wlan //进入无线配置
[AC-wlan-view]ap-group name ap-group1 //配置ap组名
[AC]capwap source interface Vlanif 200 //配置AC与AP通信的源接口
[AC-wlan-view]regulatory-domain-profile name domain1 //创建域管理模板名字
[AC-wlan-regulate-domain-domain1]country-code CN //配置AC的国家码
[AC-wlan-view]ap-group name ap-group1
[AC-wlan-ap-group-ap-group1]regulatory-domain-profile domain1 //绑定域管理模板到AP组
[AC-wlan-view]ap auth-mode mac-auth //采用MAC地址认证方式
[AC-wlan-view]ap-mac 00e0-fcab-3420 //绑定AP1的MAC地址（dis interface vlanif 1可查看MAC地址）
[AC-wlan-ap-0]ap-name a1 //绑定AP1
[AC-wlan-ap-0]ap-group ap-group1 //绑定组1
[AC-wlan-view]ap-mac 00e0-fc2f-78c0 ap-id 1 //绑定AP2的MAC地址
[AC-wlan-ap-1]ap-name a2
[AC-wlan-ap-1]ap-group ap-group1
6.配置wlan业务参数
[AC-wlan-view]security-profile name security-1 //配置安全模板
[AC-wlan-view]ssid-profile name a1 //配置SSID模板
[AC-wlan-ssid-prof-a1]ssid a1
[AC-wlan-view]vap-profile name a1-vap ce//配置vap模板
[AC-wlan-vap-prof-a1-vap]forward-mode direct-forward //配置转发模式为直接转发
[AC-wlan-vap-prof-a1-vap]service-vlan vlan-id 201 //配置业务vlan为201
[AC-wlan-vap-prof-a1-vap]security-profile security-1 //调用安全模板
[AC-wlan-vap-prof-a1-vap]ssid-profile a1 //调用SSID模板
7.绑定VAP模板到AP
[AC-wlan-view]ap-group name ap-group1
[AC-wlan-ap-group-ap-group1]vap-profile a1-vap wlan 1 radio all
8.检查结果
这篇关于华为无线网络的配置——AP上的业务数据采用直接转发模式的文章就介绍到这儿，希望我们推荐的文章对编程师们有所帮助！
