本文主要是介绍hcip 7.8，希望对大家解决编程问题提供一定的参考价值，需要的开发者们随着小编来一起学习吧！
配置各个接口ip
[r1-GigabitEthernet0/0/2]ip address 14.1.1.1 24
[r1-LoopBack0]ip address 192.168.1.1 24
[r2-GigabitEthernet0/0/2]ip address 24.1.1.1 24
[r2-LoopBack0]ip ad 192.168.2.1 24
[r3-GigabitEthernet0/0/2]ip ad 34.1.1.1 24
[r3-LoopBack0]ip ad 192.168.3.1 24
[r4-GigabitEthernet0/0/0]ip address 14.1.1.2 24
[r4-GigabitEthernet0/0/1]ip address 24.1.1.2 24
[r4-GigabitEthernet0/0/2]ip address 34.1.1.2 24
然后开始做静态路由，让公网先通起来
[r1-Tunnel0/0/0]ip address 10.1.1.1 24
[r1-Tunnel0/0/0]tunnel-protocol gre p2mp
[r1-Tunnel0/0/0]source 14.1.1.1
[r1-Tunnel0/0/0]nhrp network-id 100
[r1-Tunnel0/0/0]nhrp entry 10.1.1.2 24.1.1.1 register
[r1-Tunnel0/0/0]nhrp entry 10.1.1.3 34.1.1.1 register
[r2-Tunnel0/0/0]ip address 10.1.1.2 24
[r2-Tunnel0/0/0]tunnel-protocol gre p2mp
[r2-Tunnel0/0/0]source 24.1.1.1
[r2-Tunnel0/0/0]nhrp network-id 100
[r3-Tunnel0/0/0]ip address 10.1.1.3 24
[r3-Tunnel0/0/0]tunnel-protocol gre p2mp
[r3-Tunnel0/0/0]source 34.1.1.1
[r3-Tunnel0/0/0]nhrp network-id 100
[r1]ospf 1 router-id 1.1.1.1
[r1-ospf-1-area-0.0.0.0]network 192.168.1.1 0.0.0.0
[r1-ospf-1-area-0.0.0.0]network 10.1.1.1 0.0.0.0
[r2]ospf 1 router-id 2.2.2.2
[r2-ospf-1-area-0.0.0.0]network 192.168.2.1 0.0.0.0
[r2-ospf-1-area-0.0.0.0]network 10.1.1.0 0.0.0.0
[r3]ospf 1 router-id 3.3.3.3
[r3-ospf-1-area-0.0.0.0]network 10.1.1.3 0.0.0.0
[r3-ospf-1-area-0.0.0.0]network 192.168.3.1 0.0.0.0
[r2-Tunnel0/0/0]nhrp entry multicast dynamic
[r3-Tunnel0/0/0]nhrp entry multicast dynamic
这篇关于hcip 7.8的文章就介绍到这儿，希望我们推荐的文章对编程师们有所帮助！
