双网关备份(bfd+VRRP+策略路由配置)企业网搭建

2023-10-21 00:36
文章标签 配置 路由 搭建 企业 网关 策略 备份 vrrp bfd

本文主要是介绍双网关备份(bfd+VRRP+策略路由配置)企业网搭建，希望对大家解决编程问题提供一定的参考价值，需要的开发者们随着小编来一起学习吧！

设备选型

vlan规划

Ip地址规划

产品名字

产品型号

设备命名

登录密码

路由器

Ar2220

Dianxin

123456

路由器

Ar2220

Dianxin

123456

路由器

Ar2220

Liantong

123456

路由器

Ar2220

R3

123456

交换机

S5700

S1

123456

交换机

S5700

S2

123456

交换机

S3700

S3

123456

集线器

Hub

H1

集线器

Hub

H2

产品型号

设备命名

接口

Ip地址

AR2220

Dianxin

G0/0/1

/24

AR2220

Dianxin

G0/0/2

13.13.13.13/24

AR2220

Dianxin

G0/0/0

1.1.1.1/24

AR2220

Dianxin

G4/0/0

/24

Ar2220

Liantong

G0/0/1

/24

Ar2220

Liantong

G0/0/2

37.37.37.37/24

Ar2220

Liantong

G0/0/0

31.31.31.31/24

Ar2220

Liantong

G4/0/0

/24

Ar2220

R3

G0/0/1

Ar2220

R3

G0/0/0

S5700

S1

G0/0/1

Vlan100

S5700

S1

G0/0/2

Vlan200

S5700

S1

G0/0/3

E-trunk 1

S5700

S1

G0/0/4

E-trunk 1

S5700

S2

G0/0/1

Vlan200

S5700

S2

G0/0/2

Vlan100

S5700

S2

G0/0/3

E-trunk 1

S5700

S2

G0/0/4

E-trunk 1

实验拓扑

基础配置

Vlan划分以及IP配置

S3

<Huawei>sy

Enter system view, return user view with Ctrl+Z.

[Huawei]sys S3

[S3]  v b 10 20

[S3]int e0/0/1

[S3-Ethernet0/0/1]p l t

[S3-Ethernet0/0/1]p t a v 10 20

[S3-Ethernet0/0/1]int e0/0/2

[S3-Ethernet0/0/2]p l t

[S3-Ethernet0/0/2]p t a v 10 20

[S3-Ethernet0/0/1]int e0/0/3

[S3-Ethernet0/0/3]p l d

[S3-Ethernet0/0/3]p d v 10

[S3-Ethernet0/0/3]int e0/0/4

[S3-Ethernet0/0/4]p l a

[S3-Ethernet0/0/4]p d v 20

S1

<Huawei>sy

Enter system view, return user view with Ctrl+Z.

[Huawei]sy s1

[s1]un in en

Info: Information center is disabled.

[s1]v b 10 20 100 200 300

Info: This operation may take a few seconds. Please wait for a moment...done.

[s1]int g0/0/5

[s1-GigabitEthernet0/0/5]p l t

[s1-GigabitEthernet0/0/5]p t a v 10 20

[s1-GigabitEthernet0/0/5]q

[s1]int e 1

[s1-Eth-Trunk1]q

[s1]int g0/0/3

[s1-GigabitEthernet0/0/3]e 1

[s1-GigabitEthernet0/0/3]int g0/0/4

[s1-GigabitEthernet0/0/4]e 1

[s1]int g0/0/2

[s1-GigabitEthernet0/0/2]p l d

[s1-GigabitEthernet0/0/2]p d v 200

[s1-GigabitEthernet0/0/2]int g0/0/1

[s1-GigabitEthernet0/0/1]p l d

[s1-GigabitEthernet0/0/1]p d v 100

[s1-GigabitEthernet0/0/1]int e 1

[s1-Eth-Trunk1]p l t

[s1-Eth-Trunk1]p t p v 300

[s1-Eth-Trunk1]p t a v 300

[s1-Eth-Trunk1]p t a v 300 10 20  100 200

[s1-Eth-Trunk1]q

[s1]int v 10

[s1-Vlanif10]ip add 192.168.1.1 24

[s1-Vlanif10]q

[s1]int v 300

[s1-Vlanif300]ip add 172.16.1.1 24

[s1-Vlanif300]int v 100

[s1-Vlanif100]ip add 1.1.1.2 24

[s1-Vlanif100]int v 200

[s1-Vlanif200]ip add 3.3.3.4 24

[s1]int v 20

[s1-Vlanif20]ip add 192.168.2.2 24

S2

<Huawei>sy

Enter system view, return user view with Ctrl+Z.

[Huawei]sys s2

[s2]v b 10 20 100 300 200

[s2]un in en

Info: Information center is disabled.

[s2]int g0/0/5

[s2-GigabitEthernet0/0/5]p l t

[s2-GigabitEthernet0/0/5]p t a v 10 20  

[s2-GigabitEthernet0/0/5]int e 1

[s2-Eth-Trunk1]q

[s2]int g0/0/3

[s2-GigabitEthernet0/0/3]e 1

Info: This operation may take a few seconds. Please wait for a moment...done.

[s2-GigabitEthernet0/0/3]int g0/0/4

[s2-GigabitEthernet0/0/4]e 1

Info: This operation may take a few seconds. Please wait for a moment...done.

[s2-GigabitEthernet0/0/4]int g0/0/2

[s2-GigabitEthernet0/0/2]p l a

[s2-GigabitEthernet0/0/2]p d v 100

[s2-GigabitEthernet0/0/2]int g0/0/1

[s2-GigabitEthernet0/0/1]p l a

[s2-GigabitEthernet0/0/1]p d v 200

[s2-GigabitEthernet0/0/1]int e 1

[s2-Eth-Trunk1]p l t

[s2-Eth-Trunk1]p t a v 100 200 10 20 300

[s2-Eth-Trunk1]p t p v 300

[s2-Eth-Trunk1]int v 10

[s2-Vlanif10]ip add 192.168.1.2 24

[s2-Vlanif10]int v 20

[s2-Vlanif20]ip add 192.168.2.1 24

[s2-Vlanif20]int v 300

[s2-Vlanif300]ip add 172.16.1.2 24

[s2-Vlanif300]int v 100

[s2-Vlanif100]ip add 9.9.9.10 24

[s2-Vlanif100]int v 200

[s2-Vlanif200]ip add 10.10.10.11 24

Disnxin

<Huawei>sy

Enter system view, return user view with Ctrl+Z.

[Huawei]sy dianxin

[dianxin]int g0/0/0

[dianxin-GigabitEthernet0/0/0]ip add 2.2.2.2 24

[dianxin-GigabitEthernet0/0/0]int g0/0/1

[dianxin-GigabitEthernet0/0/1]ip add 1.1.1.1 24

[dianxin-GigabitEthernet0/0/1]int g0/0/2

[dianxin-GigabitEthernet0/0/2]ip add 13.13.13.13 24

[dianxin-GigabitEthernet0/0/2]int g4/0/0

[dianxin-GigabitEthernet4/0/0]ip add 9.9.9.9 24

Liantong

<Huawei>sy

Enter system view, return user view with Ctrl+Z.

[Huawei]sy liantong

[liantong]int g0/0/0

[liantong-GigabitEthernet0/0/0]ip add 31.31.31.31 24

[liantong-GigabitEthernet0/0/0]int g0/0/2

[liantong-GigabitEthernet0/0/2]ip add 37.37.37.37 24

[liantong-GigabitEthernet0/0/2]int g4/0/0

[liantong-GigabitEthernet4/0/0]ip add 3.3.3.3 24

[liantong-GigabitEthernet4/0/0]int g0/0/1

[liantong-GigabitEthernet0/0/1]ip add 10.10.10.10 24

Ip地址池和网关配置

S2

<s2>sy

Enter system view, return user view with Ctrl+Z.

[s2]dhcp e

Info: The operation may take a few seconds. Please wait for a moment.done.

[s2]int v 10

[s2-Vlanif10]dhcp sel int

[s2-Vlanif10]dhcp server static-bind ip-address 192.168.1.253 mac-address 5489-9858-03F4

[s2-Vlanif10]int v 20

[s2-Vlanif20]dhcp sel int

S1

<s1>sy

Enter system view, return user view with Ctrl+Z.

[s1]dhcp e

Info: The operation may take a few seconds. Please wait for a moment.done.

[s1]int v 10

[s1-Vlanif10]dhcp sel int

[s1-Vlanif10]dhcp ser

[s1-Vlanif10]dhcp server  s

[s1-Vlanif10]dhcp server  static-bind  ip

[s1-Vlanif10]dhcp server  static-bind  ip-address  192.168.1.253 ma

[s1-Vlanif10]dhcp server  static-bind  ip-address  192.168.1.253 mac-address 5489-9858-03F4

[s1-Vlanif10]int v 20

[s1-Vlanif20]dhcp sel int

Mstp配置

S1

<s1>sy

Enter system view, return user view with Ctrl+Z.

[s1]stp mode  mstp

[s1]stp region-configuration  

[s1-mst-region]region-name lwh

[s1-mst-region]instance  1 vlan  10

[s1-mst-region]instance  2 vlan  20

[s1-mst-region]active  region-configuration

Info: This operation may take a few seconds. Please wait for a moment...done.

[s1-mst-region]q

[s1]stp instance  1  root  primary  

[s1]stp instance  2 root  secondary  

S2

<s2>sy

Enter system view, return user view with Ctrl+Z.

[s2]stp mode  mstp

[s2]stp region-configuration

[s2-mst-region]region-name lwh

[s2-mst-region]instance  1 vlan  10

[s2-mst-region]instance  2 vlan  20

[s2-mst-region]active  region-configuration

Info: This operation may take a few seconds. Please wait for a moment...done.

[s2-mst-region]q

[s2]stp instance  1 root  secondary

[s2]stp instance  2 root  primary

S3

<S3>sy

Enter system view, return user view with Ctrl+Z.

[S3]stp mode mstp

[S3]stp region-configuration

[S3-mst-region]instance  1 vlan  10

[S3-mst-region]instance  2 v 20

[S3-mst-region]region-name lwh

[S3-mst-region]active region-configuration

Info: This operation may take a few seconds. Please wait for a moment...done.

[S3-mst-region]q

效果

[S3]dis stp instance 1 b

 MSTID  Port                        Role  STP State     Protection

   1    Ethernet0/0/1               ROOT  FORWARDING      NONE

   1    Ethernet0/0/2               ALTE  DISCARDING      NONE

   1    Ethernet0/0/3               DESI  FORWARDING      NONE

[S3]dis stp instance 2 b

 MSTID  Port                        Role  STP State     Protection

   2    Ethernet0/0/1               ALTE  DISCARDING      NONE

   2    Ethernet0/0/2               ROOT  FORWARDING      NONE

   2    Ethernet0/0/4               DESI  FORWARDING      NONE

[S3]

Vrrp和bfd在交换机上的配置

S1

<s1>sy

Enter system view, return user view with Ctrl+Z.

[s1]int v 10

[s1-Vlanif10]vrrp vrid  1 virtual-ip  192.168.1.254

[s1-Vlanif10]vrrp vrid  1 priority 110

[s1-Vlanif10]q

[s1]int v 20

[s1-Vlanif20]vrrp vrid  2 virtual-ip  192.168.2.254

[s1-Vlanif20]vrrp vrid  2 priority 90

S2

<s2>sy

Enter system view, return user view with Ctrl+Z.

[s2]int v 10

[s2-Vlanif10]vrrp vrid  1 virtual-ip  192.168.1.254

[s2-Vlanif10]vrrp vrid 1 priority 90

[s2-Vlanif10]int v 20

[s2-Vlanif20]vrrp vrid  2 virtual-ip  192.168.2.254

[s2-Vlanif20]vrrp vrid  2 priority 110

[s2-Vlanif20]

S1

<s2>sy

Enter system view, return user view with Ctrl+Z.

[s1]bfd lwh bind  peer-ip 192.168.2.1  source-ip 192.168.2.2 auto

[s1-bfd-session-lwh]discriminator local  2

[s1-bfd-session-lwh]discriminator remote  1

[s1-bfd-session-lwh]min-tx-interval 101

[s1-bfd-session-lwh]min-rx-interval 102

[s1-bfd-session-lwh]commit

[s1-bfd-session-lwh]q

[s1]bfd lsl bind  peer-ip 192.168.1.2  source-ip 192.168.1.1 auto

[s1-bfd-session-lsl]discriminator local  3

[s1-bfd-session-lsl]discriminator remote  4

[s1-bfd-session-lsl]min-tx-interval 103

[s1-bfd-session-lsl]min-rx-interval 104

[s1-bfd-session-lsl]commit

S2

<s2>sy

Enter system view, return user view with Ctrl+Z.

[s2]bfd

[s2-bfd]q

[s2]bfd lwh bind  peer-ip 192.168.2.2  source-ip 192.168.2.1 auto

[s2-bfd-session-lwh]discriminator local  1

[s2-bfd-session-lwh]discriminator remote  2

[s2-bfd-session-lwh]min-tx-interval 102

[s2-bfd-session-lwh]min-tx-interval 101

[s2-bfd-session-lwh]commit

[s2-bfd-session-lwh]q

[s2]bfd lsl bind  peer-ip 192.168.1.1  source-ip 192.168.1.2 auto

[s2-bfd-session-lsl]discriminator local  4

[s2-bfd-session-lsl]discriminator remote  3

[s2-bfd-session-lsl]min-tx-interval 103

[s2-bfd-session-lsl]min-rx-interval 104

[s2-bfd-session-lsl]commit

[s2-bfd-session-lsl]q

效果

<s1>dis bfd session all

--------------------------------------------------------------------------------

Local Remote     PeerIpAddr      State     Type        InterfaceName            

--------------------------------------------------------------------------------

8192  8192       192.168.2.1     Up        S_AUTO_PEER       -                  

3     4          192.168.1.2     Up        S_IP_PEER         -                  

--------------------------------------------------------------------------------

     Total UP/DOWN Session Number : 2/0

策略路由（未做）（s2）

<s1>sy

Enter system view, return user view with Ctrl+Z.

第一步

[s1]acl 3000

[s1-acl-adv-3000]rule  5 permit  ip source   192.168.1.0 0.0.0.255

[s1-acl-adv-3000]q

[s1]acl 3001

[s1-acl-adv-3001]rule  5 permit  ip source  192.168.2.0 0.0.0.255

[s1-acl-adv-3001]q

第二步

[s1]traffic classifier todianxin

[s1-classifier-todianxin]if-match  acl  3000

[s1-classifier-todianxin]q

[s1]traffic classifier  toliantong

[s1-classifier-toliantong]if

[s1-classifier-toliantong]if-match  acl 3001

[s1-classifier-toliantong]q

第三步

[s1]traffic behavior todianxin

[s1-behavior-todianxin]redirect ip-nexthop 172.16.3.1

[s1-behavior-todianxin]q

[s1]traffic behavior  toliantong

[s1-behavior-toliantong]redirect  ip-nexthop 172.16.5.1

[s1-behavior-toliantong]q

第四步

[s1]traffic policy 1

[s1-trafficpolicy-1]classifier todianxin behavior  todianxin

[s1-trafficpolicy-1]classifier  toliantong behavior  toliantong

[s1-trafficpolicy-1]q

第五步

[s1]int g0/0/5

[s1-GigabitEthernet0/0/5]traffic-policy 1 inbound

<s1>sy

Enter system view, return user view with Ctrl+Z.

第一步

[s1]acl 3000

[s1-acl-adv-3000]rule  5 permit  ip source   192.168.1.0 0.0.0.255

[s1-acl-adv-3000]q

[s1]acl 3001

[s1-acl-adv-3001]rule  5 permit  ip source  192.168.2.0 0.0.0.255

[s1-acl-adv-3001]q

第二步

[s1]traffic classifier todianxin

[s1-classifier-todianxin]if-match  acl  3000

[s1-classifier-todianxin]q

[s1]traffic classifier  toliantong

[s1-classifier-toliantong]if

[s1-classifier-toliantong]if-match  acl 3001

[s1-classifier-toliantong]q

第三步

[s1]traffic behavior todianxin

[s1-behavior-todianxin]redirect ip-nexthop 172.16.2.1

[s1-behavior-todianxin]q

[s1]traffic behavior  toliantong

[s1-behavior-toliantong]redirect  ip-nexthop 172.16.4.1

[s1-behavior-toliantong]q

第四步

[s1]traffic policy 1

[s1-trafficpolicy-1]classifier todianxin behavior  todianxin

[s1-trafficpolicy-1]classifier  toliantong behavior  toliantong

[s1-trafficpolicy-1]q

第五步

[s1]int g0/0/5

[s1-GigabitEthernet0/0/5]traffic-policy 1 inbound

Ospf配置

S1

[s1]ospf

[s1-ospf-1]dis th

#

ospf 1

 area 0.0.0.0

  network 192.168.1.0 0.0.0.255

  network 192.168.2.0 0.0.0.255

  network 172.16.2.0 0.0.0.255

  network 172.16.4.0 0.0.0.255

#

Return

S2

[s2-ospf-1]dis th

#

ospf 1

 area 0.0.0.0

  network 172.16.3.0 0.0.0.255

  network 172.16.5.0 0.0.0.255

  network 172.16.1.0 0.0.0.255

#

return

[s2-ospf-1]

R1

[dianxin]ospf

[dianxin-ospf-1]dis th

[V200R003C00]

#

ospf 1

 area 0.0.0.0

  network 172.16.2.0 0.0.0.255

  network 172.16.3.0 0.0.0.255

#

R2

[V200R003C00]

#

ospf 1

 area 0.0.0.0

  network 172.16.4.0 0.0.0.255

  network 172.16.5.0 0.0.0.255

#

Return

静态地址配置

S1

ip route-static 0.0.0.0 0.0.0.0 172.16.2.1

ip route-static 0.0.0.0 0.0.0.0 172.16.4.1

S2

ip route-static 0.0.0.0 0.0.0.0 172.16.5.1

ip route-static 0.0.0.0 0.0.0.0 172.16.3.1

R1

#

ip route-static 0.0.0.0 0.0.0.0 1.1.1.2

ip route-static 0.0.0.0 0.0.0.0 31.31.31.32 preference 50

#

ip route-static 0.0.0.0 0.0.0.0 31.31.31.32

ip route-static 0.0.0.0 0.0.0.0 1.1.1.2 preference 50

这篇关于双网关备份(bfd+VRRP+策略路由配置)企业网搭建的文章就介绍到这儿，希望我们推荐的文章对编程师们有所帮助！


http://www.chinasem.cn/article/250736。

相关文章

SpringBoot多环境配置数据读取方式

SpringBoot多环境配置数据读取方式

《SpringBoot多环境配置数据读取方式》SpringBoot通过环境隔离机制,支持properties/yaml/yml多格式配置,结合@Value、Environment和@Configura... 目录一、多环境配置的核心思路二、3种配置文件格式详解2.1 properties格式（传统格式）1.
阅读更多...
Python实现网格交易策略的过程

Python实现网格交易策略的过程

《Python实现网格交易策略的过程》本文讲解Python网格交易策略,利用ccxt获取加密货币数据及backtrader回测,通过设定网格节点,低买高卖获利,适合震荡行情,下面跟我一起看看我们的第一... 网格交易是一种经典的量化交易策略，其核心思想是在价格上下预设多个“网格”，当价格触发特定网格时执行买
阅读更多...
Oracle数据库定时备份脚本方式(Linux)

Oracle数据库定时备份脚本方式(Linux)

《Oracle数据库定时备份脚本方式(Linux)》文章介绍Oracle数据库自动备份方案,包含主机备份传输与备机解压导入流程,强调需提前全量删除原库数据避免报错,并需配置无密传输、定时任务及验证脚本... 目录说明主机脚本备机上自动导库脚本整个自动备份oracle数据库的过程（建议全程用root用户）总结
阅读更多...
Debian系和Redhat系防火墙配置方式

Debian系和Redhat系防火墙配置方式

《Debian系和Redhat系防火墙配置方式》文章对比了Debian系UFW和Redhat系Firewalld防火墙的安装、启用禁用、端口管理、规则查看及注意事项,强调SSH端口需开放、规则持久化,... 目录Debian系UFW防火墙1. 安装2. 启用与禁用3. 基本命令4. 注意事项5. 示例配置R
阅读更多...
Python极速搭建局域网文件共享服务器完整指南

Python极速搭建局域网文件共享服务器完整指南

《Python极速搭建局域网文件共享服务器完整指南》在办公室或家庭局域网中快速共享文件时,许多人会选择第三方工具或云存储服务,但这些方案往往存在隐私泄露风险或需要复杂配置,下面我们就来看看如何使用Py... 目录一、android基础版：HTTP文件共享的魔法命令1. 一行代码启动HTTP服务器2. 关键参
阅读更多...
PyCharm中配置PyQt的实现步骤

PyCharm中配置PyQt的实现步骤

《PyCharm中配置PyQt的实现步骤》PyCharm是JetBrains推出的一款强大的PythonIDE,结合PyQt可以进行pythion高效开发桌面GUI应用程序,本文就来介绍一下PyCha... 目录1. 安装China编程PyQt1.PyQt 核心组件2. 基础 PyQt 应用程序结构3. 使用 Q
阅读更多...
Redis MCP 安装与配置指南

Redis MCP 安装与配置指南

《RedisMCP安装与配置指南》本文将详细介绍如何安装和配置RedisMCP,包括快速启动、源码安装、Docker安装、以及相关的配置参数和环境变量设置,感兴趣的朋友一起看看吧... 目录一、Redis MCP 简介二、安www.chinasem.cn装 Redis MCP 服务2.1 快速启动（推荐）2.
阅读更多...
Spring Boot配置和使用两个数据源的实现步骤

Spring Boot配置和使用两个数据源的实现步骤

《SpringBoot配置和使用两个数据源的实现步骤》本文详解SpringBoot配置双数据源方法,包含配置文件设置、Bean创建、事务管理器配置及@Qualifier注解使用,强调主数据源标记、代... 目录Spring Boot配置和使用两个数据源技术背景实现步骤1. 配置数据源信息2. 创建数据源Be
阅读更多...
Spring Boot Maven 插件如何构建可执行 JAR 的核心配置

Spring Boot Maven 插件如何构建可执行 JAR 的核心配置

《SpringBootMaven插件如何构建可执行JAR的核心配置》SpringBoot核心Maven插件,用于生成可执行JAR/WAR,内置服务器简化部署,支持热部署、多环境配置及依赖管理... 目录前言一、插件的核心功能与目标1.1 插件的定位1.2 插件的 Goals（目标）1.3 插件定位1.4 核
阅读更多...
RabbitMQ消息总线方式刷新配置服务全过程

RabbitMQ消息总线方式刷新配置服务全过程

《RabbitMQ消息总线方式刷新配置服务全过程》SpringCloudBus通过消息总线与MQ实现微服务配置统一刷新,结合GitWebhooks自动触发更新,避免手动重启,提升效率与可靠性,适用于配... 目录前言介绍环境准备代码示例测试验证总结前言介绍在微服务架构中，为了更方便的向微服务实例广播消息，
阅读更多...

Copyright China编程 23002807@qq.com

沪ICP备2023033072号-2